- #How to fix ieee 1284 controller how to#
- #How to fix ieee 1284 controller driver#
- #How to fix ieee 1284 controller free#
#How to fix ieee 1284 controller driver#
IManufacturer 1 Belk USB Printing SupportīInterfaceClass 255 Vendor Specific Class begin snipped output of sudo lsusb -vvvīus 002 Device 002: ID 050d:0002 Belkin ComponentsīDeviceClass 0 (Defined at Interface level) Trausch Internet Mail & Jabber: (404) 592-5746 x1 I have also included the relevant section of the output of
#How to fix ieee 1284 controller free#
I hope that I have provided enough information if not please feel free Would that maybe provide enough information to get it going Piece of hardware under a different operating system and it works, (The kernel panics, so Iĭon't even get the chance to try.) If I can try to test this To support this controller/wire, but it doesn't even boot on my With other systems that claim to drive this piece of hardware. (2) I (attempted to) read through usblp.c and friends and compare them Would be necessary to fix this? I would be happy to testĪnything with potential to get this going. It? If not, can I somehow provide the necessary information that
#How to fix ieee 1284 controller how to#
(1) Has anyone seen this problem, and maybe knows how to work around Is that the IEEE1284 controller inside of this thing is expecting someĭifferent treatment than what it is getting from usblp or uss720. Of this stuff, cut down to 5 lines by sort and uniq):ĭrivers/usb/misc/uss720.c: async_complete: urb error -104ĭrivers/usb/misc/uss720.c: async_complete: urb error -32ĭrivers/usb/misc/uss720.c: async_complete: urb error -62ĭrivers/usb/misc/uss720.c: get_1284_register timeoutĭrivers/usb/misc/uss720.c: get_1284_register: usb error -32 It left behind lots ofĮrrors, too (I am only showing one of each but there were 6,435 lines Worse, I had to restart my system to get the thing back out of memory,īecause once it was there, it wouldn't leave. However, this failed horribly it wouldn't even talk. So, my travels then led me to try using the uss720 driver to talk to the The only result that had was to show this up repeatedly in the kernel'sĭrivers/usb/class/usblp.c: usblp0: error -115 writing to printer To force the kernel to use unidirectional mode: I then attempted to modify the usblpĭriver by adding the following to the quirk_printers structure array, I have tried using the usblp driver (which the kernel tries to use byĭefault), which was a no go. Port, so I know that this isn't an issue with the printer itself. It worked perfectly with my previous computer, which had a parallel This is a standard, ASCII handling,ĭot-matrix printer that is Epson compatible. Matter how it is submitted (including redirected directly to the printer On-line additionally, it loses the first byte of the print job no Or until I take the printer off-line and then put the printer back I can do "cat /proc/cpuinfo > /dev/usblp0", and it will hang forever.
Many hours of googling around and looking at everything I could find, I USB->Parallel converter (a Belkin F5U002 Revision 2 wire).
Long story short: I have a computer without a parallel port, and a Previous message: Zhenyu Wang: " intel_agp: fix GTT map size on G33".Next message: Pavel Machek: "slow resume (was Re: 2.6.23-rc5: known regressions)".Linux-Kernel Archive: Belkin F5U002, usblp, uss720 issues Belkin F5U002, usblp, uss720 issues From: Michael B.